Avalia??o da for?a de uni?o de diferentes t?cnicas de soldagem para uso em ortodontia

Autor: Henkin, Fernanda de Souza
Jazyk: portugalština
Rok vydání: 2017
Předmět:
Zdroj: Biblioteca Digital de Teses e Dissertações da PUC_RSPontifícia Universidade Católica do Rio Grande do SulPUC_RS.
Druh dokumentu: masterThesis
Popis: Submitted by Caroline Xavier (caroline.xavier@pucrs.br) on 2017-06-30T18:49:20Z No. of bitstreams: 1 DIS_FERNANDA_DE_SOUZA_HENKIN_PARCIAL.pdf: 153660 bytes, checksum: cc61f5fcacec40f72a7ba7bfb17c4045 (MD5)
Approved for entry into archive by Caroline Xavier (caroline.xavier@pucrs.br) on 2017-06-30T18:49:25Z (GMT) No. of bitstreams: 1 DIS_FERNANDA_DE_SOUZA_HENKIN_PARCIAL.pdf: 153660 bytes, checksum: cc61f5fcacec40f72a7ba7bfb17c4045 (MD5)
Made available in DSpace on 2017-06-30T18:49:32Z (GMT). No. of bitstreams: 1 DIS_FERNANDA_DE_SOUZA_HENKIN_PARCIAL.pdf: 153660 bytes, checksum: cc61f5fcacec40f72a7ba7bfb17c4045 (MD5) Previous issue date: 2017-01-19
Introduction: During orthodontic treatment, the use of appliances and devices that require welding procedures is often needed. Besides conventional silver soldering, different joining methods ? with potentially higher biocompatibility ? can be used. The mechanical strength of the welded areas is critical for their success, and must be evaluated. Objective: To review the joining methods for orthodontic purpose and evaluate the strength ? by tensile strength measurements ? of Silver Soldering, Spot, laser and TIG welding. Materials and Methods: 40 stainless steel wire segments with 0.8 mm diameter (Morelli, Sorocaba/SP, Brasil) were joined by means of silver soldering, spot, laser and TIG welding. For each joining method, 10 specimens were produced. Tensile strength test was performed 24 hours after welding by means of a universal testing machine (Instron Corporation, Canton, USA) using a cell load of 1000 N with a crosshead speed of 10 mm/minute. Results: The highest tensile strenght mean values was obtained by silver soldering (532.1N), followed by laser (419.8N), spot (301.1N) and TIG (216,3N) welding. Statistically significant diferences were observed between the groups, and the Dunn post-hoc test revealed difference between laser and spot welding (p=0046), laser and tig (p=0.016), spot and silver (p=2.5e-05) and silver and TIG (p=4.6e-06). Conclusions: The strenght of the laser joints are comparable to the Silver soldering joints, and represent a favorable alternative for orthodontic use. The spot and TIG welding methods presented comparable and significantly lower strenghts in relation do laser and silver soldering methods.
Introdu??o: Durante o tratamento ortod?ntico, frequentemente s?o utilizados dispositivos e aparelhos auxiliares que requerem soldagem para a sua confec??o. Al?m do processo de soldagem convencional ? prata, diferentes m?todos ? potencialmente mais biocompat?veis - podem ser utilizados. A resist?ncia mec?nica destas soldas ? fundamental para seu sucesso e deve ser avaliada. Objetivo: Revisar os m?todos de soldagem dispon?veis para uso em Ortodontia e avaliar a for?a de uni?o das soldas ? tra??o em soldas ponto, prata, laser e TIG. Materiais e M?todos: 40 segmentos de fio de a?o inoxid?vel de 0,8mm (Morelli, Sorocaba/SP, Brasil) foram soldados entre si atrav?s das t?cnicas de soldagem el?trica, ? prata, a laser e TIG, sendo realizadas 10 soldagens para cada t?cnica. Foi realizado ensaio de tra??o por meio de uma m?quina de ensaios universal (Emic DL- 2000), utilizando c?lula de carga de 1000 N e velocidade de 10 mm/min. Resultados: O grupo de soldagem ? prata apresentou a maior m?dia de resist?ncia ? tra??o (532,1N), seguido pelos grupos laser (419,8N), ponto (301,1N) e TIG (216,3N) respectivamente. Houve diferen?a significativa entre os grupos, e partir do teste post-hoc de Dunn identificou-se que esta diferen?a ocorreu entre os grupos laser e ponto (p=0,046), laser e TIG (p=0,016), ponto e prata (p=2,5e-05) e prata e tig (p=4,6e-06). Conclus?es: A for?a de uni?o de soldagens a laser pode ser compar?vel com ? de soldagens ? prata e apresenta-se como boa alternativa para uso em Ortodontia. As t?cnicas de soldagem a ponto e a TIG apresentaram for?a de uni?o compar?veis e significativamente inferiores aos das soldagens a laser e ? prata.
Databáze: Networked Digital Library of Theses & Dissertations
Externí odkaz: