Simulation of the OECD/NEA Sandia Fuel Project Phases I & II ignition tests with DRACCAR
| Autor: | O. de Luze, G. Guillard, F. Jacq |
|---|---|
| Přispěvatelé: | PSN-RES/SEMIA/LIMAR, Institut de Radioprotection et de Sûreté Nucléaire (IRSN) |
| Rok vydání: | 2018 |
| Předmět: |
Work (thermodynamics)
Nuclear engineering 02 engineering and technology US Nuclear Regulatory Commission 01 natural sciences 7. Clean energy 010305 fluids & plasmas law.invention HT Loss Of Coolant Accident PBR law Phase (matter) 0202 electrical engineering electronic engineering information engineering General Materials Science Pilling and Bedworth Ratio Safety Risk Reliability and Quality Waste Management and Disposal Flow Rate LOCA Sandia Fuel Pro- ject [PHYS]Physics [physics] Spent Fuel Pool 2 Zirconium alloy ____________________________________________________________________________________________ Abbreviations: CA KIT Heat Transfer Power (physics) Institut de Radioprotection et de Sûreté Nucléaire IRSN PA Convection DRACCAR Nuclear and High Energy Physics 020209 energy chemistry.chemical_element Déformation et Renoyage d'un Assemblage de Crayons Combus- tibles pendant un Accident de Refroidissement FR SFP US-NRC 0103 physical sciences Central Assembly Zirconium Mechanical Engineering Karlsruhe Institute of Technology Ignition system Nuclear Energy and Engineering chemistry Peripheral Assembly Environmental science Transient (oscillation) |
| Zdroj: | Nuclear Engineering and Design Nuclear Engineering and Design, Elsevier, 2018, 330, pp.524-537. ⟨10.1016/j.nucengdes.2018.01.047⟩ |
| ISSN: | 0029-5493 |
| DOI: | 10.1016/j.nucengdes.2018.01.047 |
| Popis: | International audience; This paper describes simulations of two ignition tests performed at full power in the frame of the Sandia Fuel Project (SFP) with the thermo-mechanical code DRACCAR v2.3. The OECD/NEA Sandia Fuel Project was built on an agreement between 12 countries from OECD, the Nuclear Energy Agency (NEA) and the US-NRC for the characterization of thermal-hydraulic and zirconium fire phenomena in pressurized-water reactor (PWR). The experimental program was split in two phases to focus at first on axial heating and burn propagation in one prototypic fuel assembly (Phase I), and then on axial and radial heating and burn propagation in 1 × 4 fuel assemblies (Phase II). DRACCAR is a simulation tool, developed at IRSN, for fuel assembly mechanical behavior and coolability assessment during a LOCA transient. The flexibility of DRACCAR allows the modeling of many kinds of geometries. Because the code is based on a 3D non-structured meshing, it can be used to model any non-axisymmetric geometry, like the 1 × 4 fuel assemblies geometry of the Phase II of the SFP program. In order to check the consistency of the modeling, we have optimized the code options to get best results for the Phase I, and applied the same options to the Phase II. Most of the DRACCAR results have been successfully checked against experimental ones, using additional code improvements. Air oxidation and breakaway modeling of the zircaloy claddings were successfully tested against the experimental results. Nevertheless parts of the experimental results of Phase II have been difficult to reproduce. As many causes could be involved in these difficulties, such as detailed evolution of the air convective loop, radiative heat transfers in the bundles, and the modeling of additional reactions of zirconium with nitrogen in places where oxygen is lacking, there is still room for improvement in the work of interpretation and modeling of the SFP tests. © 2018 Elsevier B.V. |
| Databáze: | OpenAIRE |
| Externí odkaz: |
|
Full Text from ScienceDirect