Stresses Distribution in Spot, Bonded, and Weld- Bonded Joints during the Process of Axial Load

Autor: Al-Bahkali, Essam A., Es-Saheb, Mahir H., Herwan, Jonny
Jazyk: angličtina
Rok vydání: 2012
Předmět:
DOI: 10.5281/zenodo.1062464
Popis: In this study the elastic-plastic stress distribution in weld-bonded joint, fabricated from austenitic stainless steel (AISI 304) sheet of 1.00 mm thickness and Epoxy adhesive Araldite 2011, subjected to axial loading is investigated. This is needed to improve design procedures and welding codes, and saving efforts in the cumbersome experiments and analysis. Therefore, a complete 3-D finite element modelling and analysis of spot welded, bonded and weld-bonded joints under axial loading conditions is carried out. A comprehensive systematic experimental program is conducted to determine many properties and quantities, of the base metals and the adhesive, needed for FE modelling, such like the elastic – plastic properties, modulus of elasticity, fracture limit, the nugget and heat affected zones (HAZ) properties, etc. Consequently, the finite element models developed, for each case, are used to evaluate stresses distributions across the entire joint, in both the elastic and plastic regions. The stress distribution curves are obtained, particularly in the elastic regions and found to be consistent and in excellent agreement with the published data. Furthermore, the stresses distributions are obtained in the weld-bonded joint and display the best results with almost uniform smooth distribution compared to spot and bonded cases. The stress concentration peaks at the edges of the weld-bonded region, are almost eliminated resulting in achieving the strongest joint of all processes.
{"references":["P. K. Ghosh, and Vivek, \"Weld-bonding of stainless steel\", ISIJ\nInternational, Vol. 43, pp. 85-94, 2003.","Q. D. Yang, M. D. Thouless, and S. M. Ward, \"Elastic-plastic mode-II\nfracture of adhesive joints\", International Journal of Solids and\nStructures, Vol. 38, pp. 3251-3262, 2001.","A. Hasanbasoglu, and R. Kacar, \"Resistance spot welding of dissimilar\nmaterials (AISI 316L-DIN EN 10130-99)\", Journal of Materials and\nDesign, Vol. 28, pp. 1794-1800, 2007","I. R. Nodeh, S. Serajzadeh, and A. H. Kokabi, \"Simulation of welding\nresidual stresses in resistance spot welding, FE Modeling and X-ray\nverification\", Journal of Materials Processing Technology, Vol. 205, pp.\n60-69, 2008","A. De, M. P. Thaddeus, and L. Lorn, \"Numerical modeling of resistance\nspot welding of aluminum alloy\", ISIJ International, Vol. 43, No. 2, pp.\n238-244, 2003.","J. Z. Chen, and D. F. Farson, \"Analytical modeling of heat conduction\nfor small scale resistance spot welding process\", Journal of Materials\nProcessing Technology, Vol. 178, pp. 251-258, 2006.","X. Kong, Q. Yang, B. Li, G. Rothwell, R. English, and H. J. Ren,\n\"Numerical Study of spot-welded joints of steel\", Journal of Materials\nand Design, Vol. 29, pp. 1554-1561, 2008.","S. L, M. D. Thouless, A. M. Waas, J. A. Schroeder, and P. D. Zavattieri,\n\"Use of mode I cohesive zone models to describe the fracture of an\nadhesively-bonded polymer-matrix composite\", Journal of Composite\nScience and Technology, Vol. 65, pp. 281-293, 2005.","S. Li, M. D. Thouless, A. M. Waas, J. A. Schroeder, and P. D.\nZavattieri, \"Mixed-mode cohesive-zone models for fracture of an\nadhesively bonded polymer-matrix composite\", Journal of Engineering\nFracture Mechanics, Vol. 73, pp. 64-78, 2006.\n[10] M. You, Z. Li, X. Zheng, S. Yu, G. Li, and D. Sun, \"A numerical and\nexperimental study of performed angle in the lap zone on adhesively\nbonded steel single lap joint\", International Journal of Adhesion and\nAdhesives, Vol. 29, pp. 280-285, 2009.\n[11] M. N. Cavalli, M. D. Thouless, and Q. D. Yang, \"Cohesive-zone\nmodeling of the deformation and fracture of weld-bonded joints\",\nWelding Journal, Vol. 83, p. 133S-139S, 2004.\n[12] Y. Xia, Q. Zhou, P. C. Wang, N. L. Johnson, X. Q. Gayden, and J. D.\nFickers, \"Development of high-efficiency modeling technique for weldbonded\nsteel joints in vehicle structures-part I: static experiments and\nsimulations\", International Journal of Adhesion and Adhesives, Vol. 29,\npp. 414-426, 2009.\n[13] Z. Hou, I. S. Kim, Y. Wang, C. Li, and C. Chen, \"Finite element\nanalysis for the mechanical features of resistance spot welding process\",\nJournal of Materials Processing Technology, Vol. 185, pp. 160-165,\n2007.\n[14] X. Deng, W. Chen, and G. Shi, \"Three-dimensional finite element\nanalysis of mechanical behavior of spot welds\", Journal of Finite\nElement Analysis and Design, Vol. 35, pp. 17-39, 2000.\n[15] E. Al-bahkali , M. Es-saheb, and J. Herwan, \"Finite Element Modeling\nof Weld-Bonded Joint\", 4th International Conference on Advanced\nComputational Engineering and Experimenting, Paris, 2010.\n[16] J. Herwan, \"Load-Displacement Curve Prediction of Weld-Bonded\nStainless Steel Using Finite Element Method\", MSc thesis, King Saud\nUniversity, KSA, 2010.\n[17] ASTM, \"Standard method of tension testing of metallic materials\",\nAnnual Book of standard, ASTM-E8-81, 1981.\n[18] Huntsman Corp, \"Technical data sheet of structural adhesives araldite-\n201\", Huntsman Advanced Materials, 2007.\n[19] E. Jeon, J. Y. Kim, M. K. Baik, S. H. Kim, J. S. Park, and D. Kwon,\n\"Optimum definition of true strain beneath a spherical indenter for\nderiving indentation flow curves\", Journal of Materials Science and\nEngineering, Vol. A419, pp. 196-201, 2006.\n[20] Y. Bao,\" Dependence of ductile crack formation in tensile tests on stress\ntriaxiality stress and strain ratios\", Journal of Engineering Fracture\nMechanics, Vol. 72, pp. 502-522, 2005.\n[21] M. Alves, and N. Jones, \"Influence of hydrostatics stress on failure of\naxi-symmetric notched specimens\", Journal of the Mechanics and\nPhysics of Solids, Vol. 47, pp. 643-667, 1999.\n[22] A. C. Mackenzie, J. W. Hancock, and D. K. Brown, \"On the influence of\nstate of stress on ductile failure initiation in high strength steels\",\nJournal of Engineering Fracture Mechanics, Vol. 9, pp. 167-188, 1977.\n[23] C. Sun, M. D. Thouless, A. M. Waas, J. A. Schroeder, and P. D.\nZavattieri, \"Rate effects for mixed-mode fracture of plasticallydeforming\nadhesively-bonded structures\", International Journal of\nAdhesion and Adhesives, Vol. 29, pp. 434-443, 2009.\n[24] M. Arai, Y. Noro, K. Sugimoto, and M. Endo, \"Mode I and mode II\ninterlaminar fracture toughness of CFRP laminates toughened by carbon\nnanofiber interlayer\", Journal of Composite Science and Technology,\nVol. 68, pp. 516-525, 2008.\n[25] ABAQUS, User-s Manual, Version 6.9, 2010."]}
Databáze: OpenAIRE
Externí odkaz: