Microhardness testing of resin cement versus sonic bulk fill resin composite material for cementation of CAD/CAM composite block with different thickness
| Autor: | Haitham Amr, Ahmed Elzoheiry, Amir Hafez |
|---|---|
| Rok vydání: | 2019 |
| Předmět: |
Cement
Materials science Resin composite Composite number Bulk fill 030206 dentistry 02 engineering and technology 021001 nanoscience & nanotechnology Block (periodic table) Cementation (geology) Indentation hardness 03 medical and health sciences 0302 clinical medicine Composite material 0210 nano-technology Resin cement |
| Zdroj: | Egyptian Dental Journal. 65:407-416 |
| ISSN: | 2090-2360 |
| DOI: | 10.21608/edj.2019.72716 |
| Popis: | Objective: evaluate the microhardness and depth of cure of sonic bulk fill resin composite material for cementation of CAD/CAM composite block with different thicknesses versus the traditionally used dual cured resin cement by assessing microhardness at the top and bottom and calculating bottom/top ratio to determine the depth of cure.Materials and methods: CAD/CAM resin composite blocks (Grandio) restorative materials were used in the present study. For cementation options, two resin materials were selected: SonicFill 2 bulk fill resin composite (Kerr) and Dual-link universal Resin cement (Bisco). Four sections were prepared from each CAD/CAM blocks thickness of 1 mm, 1.5 mm, 2 mm and 3 mm respectively. Sectioned specimens of each CAD/CAM blocks were then divided according to their thickness into three groups (n=5).Portions of each composite cement were placed on a 1-mm thick transparent glass slide and squeezed to a 100µm film thickness Each specimen was covered with one of the CAD–CAM composite block slabs or left uncovered (control) and then light-cured for 40 sec that was positioned perpendicularly on top and in direct contact with the CAD–CAM slabs or the top glass (control).Micro-hardness was obtained for the top and bottom surface of specimens. The mean microhardness values and hardness ratio % of the specimens were calculated and tabulated. Microhardness measurements were performed twice; one immediately and after 24 hours. Statistical analysis was performed. Significance of the difference within the same group was evaluated using one way analysis of variance (ANOVA) test, followed by Tukey’s post hoc test when ANOVA indicated a significant difference. T test was used to compare between both groups. The level of significance was set at P < 0.05. Results: Immediately, in control, a higher mean value was recorded in Sonicfill group, with a statistically significant difference (p=0.011). In 1 mm, 1.5 mm, 2mm, a higher mean value was recorded in SonicFill 2 group, with a statistically significant difference (p=0.003, p=0.00, p=0.00 respectively). In 3 mm resin cement recorded a mean value of 0.495±0.012.After 24 hours, in control, a higher mean value was recorded in resin cement group, with no statistically significant difference (p=0.44). In 1 mm, 1.5 mm, a higher mean value was recorded in SonicFill 2 group, with no statistically significant difference (p=0.55, p=0.356 respectively). In 2 mm, resin cement recorded a significantly higher mean value (p=0.00). In 3 mm, resin cement recorded a mean value of 0.876±0.008Conclusions: Under the limitation of the current study it could be concluded that bulk fill light cured resin composite as new trend in cementation procedure can be efficiently cured through CAD/CAM composite blocks with thickness not more than 1.5mm. Indeed, dual curable resin cement remains convenient for cementation of thicker indirect esthetic restoration. |
| Databáze: | OpenAIRE |
| Externí odkaz: |
|