| Abstrakt: |
The purpose of this work is to study the influence of the activation temperature on the porous structure characteristics of carbonaceous materials (CMs) prepared from long-flame coal under thermoprogrammed activation at the KОН/coal ratio RKOH = 1.0 g/g. The CMs were obtained in argon in three stages: 1) heating (4 grad/min) to the specified temperature t in the range of 350–825 °С; 2) isothermal exposure 1 h; 3) cooling, washing from alkali and drying. Samples are denoted as CM(t). The CM yield (Y, %) and CMs elemental composition are determined. Based on low-temperature (77 K) nitrogen adsorption-desorption isotherms, integral and differential dependences of the specific surface area SDFT (m² /g) and pore volume V (cm³ /g) on the average pore diameter (D, nm) were calculated by 2D-NLDFT-НS method (SAIEUS program). They were used to define volumes of ultramicropores (Vumi), supermicropores (Vsmi) and micropores (Vmi). The total pore volume V was calculated from the nitrogen amount adsorbed at a relative pressure p/p0 ~ 1.0. The S values of ultramicropores (Sumi), supermicropores (Ssmi) and micropores (Smi) were similarly determined. The CM yield was established to decrease linearly (R² = 0.979) from 70.2 to 45.3 % with an increase in temperature from 350 to 825 °С. The carbon content decreases to a minimum value at 500 °С (72.6 %), and then increases to a maximum value (87.5 %) at 825 °С; the oxygen content changes antibatically. Two temperature regions were identified: region I (≤ 500 °С) of increasing the oxygen content due to reactions in which KOH acts as a donor of O atoms; region II (≥ 500 °C) of dominating the thermal destruction of functional groups (carboxyl, lactone, ester) with the release of CO and CO2, and condensation increasing the size of polyarenes of the CM secondary framework and formsng single Сar-Саr bonds between them. The CM(350) sample was found to contain only mesopores (D ≥ 10 nm) and macropores. An activation temperature increase to 400 °C initiates the additional formation of small-diameter micropores and mesopores. In samples CM(400) - CM(825), the main portion of newly formed pores falls on pores with D ≤ 5 nm. With increasing temperature, the micropores volume increases almost linearly (R² = 0.992). The Vumi and Vsmi volumes increase up to 600 °C. At higher temperatures the ultramicropores volume decreases due to transforming ultramicropores (D ≤ 0.7 nm) into supermicropores (D = 0.7–2.0 nm). Portion of the ultramicropores volume changes with a maximum (23.9 %) in the CM(600) sample. The SBET specific surface area linearly (R² = 0.992) increases with temperature up to 1729 m² /g. The SDFT values are close to SBET, but noticeably lower (1514–1530 m² /g) for CM(785)-CM(825). The micropores specific surface area increases to 1415 m² /g, and ultramicropore surface Sumi changes extremely with a maximum (526 m² /g) for the CM(600) sample, which should be expected based on the temperature dependence of the Vumi parameter. The decrease in Sumi values after the maximum is compensated by an increase in the supermicropore surface. Such an effect - the redistribution of pores by size in the microporous range (D ≤ 2 nm) with an increase in the alkaline activation temperature is not described in the literature. The portion of the micropores surface is dominant (92.6–97.0 %) in samples prepared at t ≥ 450 °C. The portion of the ultramicropore surface is maximum (56.3 %) in CM(500). Pores are revealed that do not form at all at 450–750 °C. These are supermicropores (D = 0.96–2.00 nm) and mesopores of small diameters (D = 2.0–2.82 nm). This effect was assumed to be due to the properties of the CM supramolecular framework, which is formed from polyarene fragments of the initial and activated coals having polyarenes with diameters of the same order (1.68–2.54 nm). [ABSTRACT FROM AUTHOR] |
