Phase determination in dual phase steels via HREBSD-based tetragonality mapping.

Autor: Adams D; Department of Mechanical Engineering, Brigham Young University, Provo, Utah., Miles MP; Department of Mechanical Engineering, Brigham Young University, Provo, Utah., Homer ER; Department of Mechanical Engineering, Brigham Young University, Provo, Utah., Brown T; General Motors Corp, Detroit, Michigan., Mishra RK; General Motors Corp, Detroit, Michigan., Fullwood DT; Department of Mechanical Engineering, Brigham Young University, Provo, Utah.
Jazyk: angličtina
Zdroj: Journal of microscopy [J Microsc] 2021 Apr; Vol. 282 (1), pp. 60-72. Date of Electronic Publication: 2020 Dec 06.
DOI: 10.1111/jmi.12980
Abstrakt: Electron Backscatter Diffraction (EBSD) is a widely used approach for characterising the microstructure of various materials. However, it is difficult to accurately distinguish similar (body centred cubic and body centred tetragonal, with small tetragonality) phases in steels using standard EBSD software. One method to tackle the problem of phase distinction is to measure the tetragonality of the phases, which can be done using simulated patterns and cross-correlation techniques to detect distortion away from a perfectly cubic crystal lattice. However, small errors in the determination of microscope geometry (the so-called pattern or projection centre) can cause significant errors in tetragonality measurement and lead to erroneous results. This paper utilises a new approach for accurate pattern centre determination via a strain minimisation routine across a large number of grains in dual phase steels. Tetragonality maps are then produced and used to identify phase and estimate local carbon content. The technique is implemented using both kinetically simulated and dynamically simulated patterns to determine their relative accuracy. Tetragonality maps, and subsequent phase maps, based on dynamically simulated patterns in a point-by-point and grain average comparison are found to consistently produce more precise and accurate results, with close to 90% accuracy for grain phase identification, when compared with an image-quality identification method. The error in tetragonality measurements appears to be of the order of 1%, thus producing a commensurate ∼0.2% error in carbon content estimation. Such an error makes the technique unsuitable for estimation of total carbon content of most commercial steels, which often have carbon levels below 0.1%. However, even in the DP steel for this study (0.1 wt.% carbon) it can be used to map carbon in regions with higher accumulation (such as in martensite with nonhomogeneous carbon content). LAY DESCRIPTION: Electron Backscatter Diffraction (EBSD) is a widely used approach for characterising the microstructure of various materials. However, it is difficult to accurately distinguish similar (BCC and BCT) phases in steels using standard EBSD software due to the small difference in crystal structure. One method to tackle the problem of phase distinction is to measure the tetragonality, or apparent 'strain' in the crystal lattice, of the phases. This can be done by comparing experimental EBSD patterns with simulated patterns via cross-correlation techniques, to detect distortion away from a perfectly cubic crystal lattice. However, small errors in the determination of microscope geometry (the so-called pattern or projection centre) can cause significant errors in tetragonality measurement and lead to erroneous results. This paper utilises a new approach for accurate pattern centre determination via a strain minimisation routine across a large number of grains in dual phase steels. Tetragonality maps are then produced and used to identify phase and estimate local carbon content. The technique is implemented using both simple kinetically simulated and more complex dynamically simulated patterns to determine their relative accuracy. Tetragonality maps, and subsequent phase maps, based on dynamically simulated patterns in a point-by-point and grain average comparison are found to consistently produce more precise and accurate results, with close to 90% accuracy for grain phase identification, when compared with an image-quality identification method. The error in tetragonality measurements appears to be of the order of 1%, thus producing a commensurate error in carbon content estimation. Such an error makes an estimate of total carbon content particularly unsuitable for low carbon steels; although maps of local carbon content may still be revealing. Application of the method developed in this paper will lead to better understanding of the complex microstructures of steels, and the potential to design microstructures that deliver higher strength and ductility for common applications, such as vehicle components.
(© 2020 Royal Microscopical Society.)
Databáze: MEDLINE
Externí odkaz:
Nepřihlášeným uživatelům se plný text nezobrazuje