The Influence of Co Additive on the Sintering, Mechanical Properties, Cytocompatibility, and Digital Light Processing Based Stereolithography of 3Y-TZP-5Al 2 O 3 Ceramics.

Autor: Goldberg M; Laboratory of Composite Ceramic Materials, A.A. Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences, 119334 Moscow, Russia., Obolkina T; Laboratory of Composite Ceramic Materials, A.A. Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences, 119334 Moscow, Russia., Smirnov S; Laboratory of Composite Ceramic Materials, A.A. Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences, 119334 Moscow, Russia., Protsenko P; Laboratory of Composite Ceramic Materials, A.A. Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences, 119334 Moscow, Russia.; Department of Chemistry, M.V. Lomonosov Moscow State University, 119991 Moscow, Russia., Titov D; Laboratory of Composite Ceramic Materials, A.A. Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences, 119334 Moscow, Russia., Antonova O; Laboratory of Composite Ceramic Materials, A.A. Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences, 119334 Moscow, Russia., Konovalov A; Laboratory of Composite Ceramic Materials, A.A. Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences, 119334 Moscow, Russia., Kudryavtsev E; Joint Research Center, Technology and Materials, Belgorod State National Research University, 308015 Belgorod, Russia., Sviridova I; Laboratory of Prediction of Cancer Treatment Response, National Medical Research Radiological Center of the Ministry of Health of the Russian Federation, 125284 Moscow, Russia., Kirsanova V; Laboratory of Prediction of Cancer Treatment Response, National Medical Research Radiological Center of the Ministry of Health of the Russian Federation, 125284 Moscow, Russia., Sergeeva N; Laboratory of Prediction of Cancer Treatment Response, National Medical Research Radiological Center of the Ministry of Health of the Russian Federation, 125284 Moscow, Russia., Komlev V; Laboratory of Composite Ceramic Materials, A.A. Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences, 119334 Moscow, Russia., Barinov S; Laboratory of Composite Ceramic Materials, A.A. Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences, 119334 Moscow, Russia.
Jazyk: angličtina
Zdroj: Materials (Basel, Switzerland) [Materials (Basel)] 2020 Jun 20; Vol. 13 (12). Date of Electronic Publication: 2020 Jun 20.
DOI: 10.3390/ma13122789
Abstrakt: Nanocrystalline 3 mol% yttria-tetragonal zirconia polycrystal (3Y-TZP) ceramic powder containing 5 wt.% Al 2 O 3 with 64 m 2 /g specific area was synthesized through precipitation method. Different amounts of Co (0-3 mol%) were introduced into synthesized powders, and ceramic materials were obtained by heat treatment in the air for 2 h at 1350-1550 °C. The influence of Co addition on the sintering temperature, phase composition, microstructure, mechanical and biomedical properties of the obtained composite materials, and on the resolution of the digital light processing (DLP) printed and sintered ceramic samples was investigated. The addition of a low amount of Co (0.33 mol%) allows us to decrease the sintering temperature, to improve the mechanical properties of ceramics, to preserve the nanoscale size of grains at 1350-1400 °C. The further increase of Co concentration resulted in the formation of both substitutional and interstitial sites in solid solution and appearance of CoAl 2 O 4 confirmed by UV-visible spectroscopy, which stimulates grain growth. Due to the prevention of enlarging grains and to the formation of the dense microstructure in ceramic based on the tetragonal ZrO 2 and Al 2 O 3 with 0.33 mol% Co the bending strength of 720 ± 33 MPa was obtained after sintering at 1400 °C. The obtained materials demonstrated the absence of cytotoxicity and good cytocompatibility. The formation of blue CoAl 2 O 4 allows us to improve the resolution of DLP based stereolithographic printed green bodies and sintered samples of the ceramics based on ZrO 2 -Al 2 O 3 . The developed materials and technology could be the basis for 3D manufacturing of bioceramic implants for medicine.
Databáze: MEDLINE
Externí odkaz:
Nepřihlášeným uživatelům se plný text nezobrazuje