Zobrazeno 1 - 10
of 45
pro vyhledávání: '"Xuye Zhuang"'
Autor:
Jiaqi Miao, Pinghua Li, Mingchen Lv, Suzhen Nie, Yang Liu, Ruimei Liang, Weijiang Ma, Xuye Zhuang
Publikováno v:
Micromachines, Vol 15, Iss 8, p 1049 (2024)
This article proposes a low cross-axis sensitivity resonant MEMS(Micro-Electro-Mechanical Systems) accelerometer that is optimized based on the BP and NSGA-II algorithms. When resonant accelerometers are used in seismic monitoring, automotive safety
Externí odkaz:
https://doaj.org/article/a2c551d0169c48cc9b3c9197569577db
Publikováno v:
Symmetry, Vol 16, Iss 6, p 720 (2024)
A soft fault in an analog circuit is a symptom where the parameter range of a component exists symmetrically to the left and right of its nominal value and exceeds a specific range. The proposed method uses the Grey Wolf Optimization (GWO) optimized
Externí odkaz:
https://doaj.org/article/24b1ee42722b47698c55a07bcd2c838b
Publikováno v:
PLoS ONE, Vol 19, Iss 2, p e0291660 (2024)
To accurately locate faulty components in analog circuits, an analog circuit fault diagnosis method based on Tunable Q-factor Wavelet Transform(TQWT) and Convolutional Neural Network (CNN) is proposed in this paper. Firstly, the Grey Wolf algorithm (
Externí odkaz:
https://doaj.org/article/3e91398b7c394c099fe24d14ea8d2f45
Publikováno v:
Micromachines, Vol 15, Iss 4, p 509 (2024)
With the continuous progress of aerospace, military technology, and marine development, the MEMS resonance pressure sensor puts forward the requirements of not only a wide range but also high sensitivity. However, traditional resonators are hardly co
Externí odkaz:
https://doaj.org/article/2e9e9be41a974fc0b94394bf999fd5c0
Publikováno v:
Micromachines, Vol 14, Iss 6, p 1161 (2023)
As an effective capacitance signal produced by a micro-hemisphere gyro is usually below the pF level, and the capacitance reading process is susceptible to parasitic capacitance and environmental noise, it is highly difficult to acquire an effective
Externí odkaz:
https://doaj.org/article/6273c7e18d16448aa96aacf7769bade8
Autor:
Jinghao Liu, Pinghua Li, Xuye Zhuang, Yunlong Sheng, Qi Qiao, Mingchen Lv, Zhongfeng Gao, Jialuo Liao
Publikováno v:
Micromachines, Vol 14, Iss 5, p 1054 (2023)
Although one of the poster children of high-performance MEMS (Micro Electro Mechanical Systems) gyroscopes, the MEMS hemispherical resonator gyroscope (HRG) is faced with the barrier of technical and process limits, which makes it unable to form a re
Externí odkaz:
https://doaj.org/article/74f1e0fd42764b919e23f90b7cd34ac0
Publikováno v:
Micromachines, Vol 14, Iss 4, p 792 (2023)
As a MEMS gyroscope is susceptible to environmental interference, its performance is degraded due to random noise. Accurate and rapid analysis of random noise of MEMS gyroscope is of great significance to improve the gyroscope’s performance. A PID-
Externí odkaz:
https://doaj.org/article/d5bad2f59ab6465abcea083dbbb5165f
Autor:
Bin Wu, Zhenyu Zhang, Junyuan Feng, Fanning Meng, Shengzuo Wan, Xuye Zhuang, Li Li, Haoran Liu, Fuxu Zhang
Publikováno v:
Materials, Vol 16, Iss 4, p 1521 (2023)
Diamond wire sawing is widely used in processing NdFeB rare earth permanent magnets. However, it induces periodic saw marks and fracture chipping pits, which severely affect the flatness and surface quality of the products. In this study, the lateral
Externí odkaz:
https://doaj.org/article/4df4190944ea40938b9f1179ca8d0a45
Autor:
Zifeng Zhao, Zhenyu Zhang, Chunjing Shi, Junyuan Feng, Xuye Zhuang, Li Li, Fanning Meng, Haodong Li, Zihang Xue, Dongdong Liu
Publikováno v:
Materials, Vol 16, Iss 3, p 1148 (2023)
Quartz glass shows superior physicochemical properties and is used in modern high technology. Due to its hard and brittle characteristics, traditional polishing slurry mostly uses strong acid, strong alkali, and potent corrosive additives, which caus
Externí odkaz:
https://doaj.org/article/8823e73f9615424ea86e3ecb25a75d3c
Autor:
Fuxu Zhang, Zhenyu Zhang, Qinming Gu, Xuezhang Hou, Fanning Meng, Xuye Zhuang, Li Li, Bingxin Liu, Junyuan Feng
Publikováno v:
Materials, Vol 16, Iss 3, p 1222 (2023)
AlSi10Mg has a good forming ability and has been widely accepted as an optimal material for selective laser melting (SLM). However, the strength and elongation of unmodified AlSi10Mg are insufficient, which limits its application in the space industr
Externí odkaz:
https://doaj.org/article/16708a603e064df7a92159f5dc497743