Zobrazeno 1 - 10
of 47
pro vyhledávání: '"Tomáš Zlámal"'
Autor:
Tomáš Zlámal
Publikováno v:
Archaeologia Historica, Vol 47, Iss 2 (2022)
Předkládaný text se věnuje dokladům středověkého osídlení Bělidel, původně olomouckého předměstí, které bylo ve 20. letech 16. století obehnáno novou městskou hradbou a stalo se tak součástí města. Přináší přehled záchr
Externí odkaz:
https://doaj.org/article/e4454141beb94d049a8d529e73b4166c
The effect of feed rate on durability and wear of exchangeable cutting inserts during cutting Ni-625
Publikováno v:
Tehnički Vjesnik, Vol 24, Iss Supplement 1, Pp 1-6 (2017)
This paper deals with the process of cutting of nickel superalloy and selection of suitable cutting parameters for its easy and effective cutting. The experimental part proposes three exchangeable inserts and determines the effect of feed rate cuttin
Externí odkaz:
https://doaj.org/article/b86f95edb68a420c9251df522e1bf2e8
Publikováno v:
Micromachines, Vol 11, Iss 2, p 166 (2020)
Nanocomposite AlCrSiN hard coatings were deposited on the cemented carbide substrates with a negative substrate bias voltage within the range of −80 to −120 V using the cathodic arc evaporation system. The effect of variation in the bias voltage
Externí odkaz:
https://doaj.org/article/cc24e3906e9c44399331257928403397
Publikováno v:
Materials Science Forum. 990:231-238
The paper deals with the issue of coating and surface finishing with edge preparation prior to the coating. Nanocomposite AlCrSiN hard coatings were deposited on WC-Co substrates with a negative substrate bias voltage in range of-80 to-120 V using ca
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::7bf9b22d78d63fbe9d96ae2a803dbe00
https://doi.org/10.4028/www.scientific.net/msf.990.231
https://doi.org/10.4028/www.scientific.net/msf.990.231
Publikováno v:
Transportation Research Procedia. 40:602-609
The article deals with the determination of influence of cutting geometry of grooving tool on intensity and course of dynamic load for longitudinal turning of carbon steel C45 (W. Nr. 1.0503). The exchangeable cutting inserts made from sintered carbi
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::456dde00cbfdfb28b5d878270dff4056
https://doi.org/10.1016/j.trpro.2019.07.086
https://doi.org/10.1016/j.trpro.2019.07.086
Publikováno v:
Advances in Science and Technology Research Journal, Vol 12, Iss 3, Pp 47-54 (2018)
This paper examines the effect of selected factors on the wood bonded joint strength. The structural factor under scrutiny was the geometry of the surface area; however, other major dimensions of adherends were compared as well. The tests were perfor
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_dedup___::2fa82b0190c44a9e77c5bbd3cdea15fc
https://doi.org/10.12913/22998624/92099
https://doi.org/10.12913/22998624/92099
Publikováno v:
Materials Science Forum. 919:84-91
The paper deals with the comparison of surface hardness and porosity of stainless steel 316L (1.4404) produced by additive technology (SLM) and cold rolled steel. The subject of the paper is a comparison of two sets of samples where the first set of
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::eb9a3328cd5839f583c7747e2f22b4c4
https://doi.org/10.4028/www.scientific.net/msf.919.84
https://doi.org/10.4028/www.scientific.net/msf.919.84
Publikováno v:
MM Science Journal. 2018:2218-2222
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::7091dca70542aa00b8a1479af85bbe26
https://doi.org/10.17973/mmsj.2018_03_201771
https://doi.org/10.17973/mmsj.2018_03_201771
Publikováno v:
MM Science Journal. 2017:1995-2003
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::cd14e8cdbd0c67ebfd91636aebff623c
https://doi.org/10.17973/mmsj.2017_12_201760
https://doi.org/10.17973/mmsj.2017_12_201760
Publikováno v:
Advances in Science and Technology Research Journal, Vol 11, Iss 4, Pp 286-293 (2017)
Advances in Science and Technology Research Journal, Vol 12, Iss 1, Pp 236-243 (2018)
Advances in Science and Technology Research Journal, Vol 12, Iss 1, Pp 236-243 (2018)
The paper deals with the design of a suitable cutting geometry of a tool for the machining of the Inconel 625 nickel alloy. This alloy is among the hard-to-machine refractory alloys that cause very rapid wear on cutting tools. Therefore, SNMG and RCM
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_dedup___::4eec22238e7a2a10e49d4fbd8a9f0d59
https://doi.org/10.12913/22998624/80925
https://doi.org/10.12913/22998624/80925