Zobrazeno 1 - 10
of 143
pro vyhledávání: '"S. Thirumalai Kumaran"'
Publikováno v:
Results in Materials, Vol 20, Iss , Pp 100487- (2023)
Producing high-quality surfaces from hard and brittle metals presents a formidable challenge that calls for a meticulous machining strategy and an effective cutting tool. The mechanism of tool failure, chip formation behavior, and micro-morphology of
Externí odkaz:
https://doaj.org/article/3263d8e453d746ee8ed66903d3f5f309
Publikováno v:
INCAS Bulletin, Vol 13, Iss 3, Pp 245-251 (2021)
Corrosion is a process that causes a change of metal to chemically stabled form, by reacting with a solution or with the atmospheric air. There are various types of corrosions such as crevice corrosion, intergranular corrosion, stress corrosion, pitt
Externí odkaz:
https://doaj.org/article/ec6a287e05934268bf12f0e5e406de62
Publikováno v:
International Journal of Lightweight Materials and Manufacture, Vol 4, Iss 1, Pp 127-144 (2021)
Electrical discharge machining (EDM) is a non-conventional machining process which was developed to machine hard to cut materials for the past few decades. In addition to this, it also used to modify the surface characteristics of the material throug
Externí odkaz:
https://doaj.org/article/3e6a79db98f14903978d854cd536113f
Publikováno v:
INCAS Bulletin, Vol 12, Iss 4, Pp 221-226 (2020)
Electrochemical corrosion behaviour on stainless steel 316 has been studied with various solutions and its corroded samples along with the microstructural studies and prevention. The electrochemical corrosion occurs due to the transformation of elect
Externí odkaz:
https://doaj.org/article/9add3a6ed8b344a7b30a761bcd339c5b
Autor:
K.M. John, S. Thirumalai Kumaran
Publikováno v:
International Journal of Lightweight Materials and Manufacture, Vol 3, Iss 4, Pp 357-364 (2020)
Drilling of composite materials is a common manufacturing process which is widely used in various applications such as aircraft and automobile assemblies. Usually, drilling of composite materials is very challenging because of their high strength, no
Externí odkaz:
https://doaj.org/article/a5d3f3ca4f18422dbf14f6c96724a91d
Investigation of WEDM process parameters of Al–SiC–B4C composites using response surface methodology
Autor:
S. Suresh Kumar, F. Erdemir, Temel Varol, S. Thirumalai Kumaran, M. Uthayakumar, Aykut Canakci
Publikováno v:
International Journal of Lightweight Materials and Manufacture, Vol 3, Iss 2, Pp 127-135 (2020)
Aluminum based composites are widely used in various engineering applications. Though the processing of these materials is easy, it requires advanced machining techniques to cut the same as it becomes harder after the addition of ceramic reinforcemen
Externí odkaz:
https://doaj.org/article/a47bcdf2ddfa4b3aa88dbcaf9bc3917e
Publikováno v:
Defence Technology, Vol 15, Iss 4, Pp 557-564 (2019)
Heat energy generated during machining has been found to have a greater influence on determining the machinability of the materials. In this work, magnesium-based silicon carbide composite, which has been identified as a suitable lightweight applicat
Externí odkaz:
https://doaj.org/article/1f79866b594146cb867414f8413a08ab
Publikováno v:
Defence Technology, Vol 15, Iss 3, Pp 338-343 (2019)
In the present work, the surface characteristics of Electrical Discharge Machined (EDM) Al (6351)SiC and Al (6351)SiCB4C composites are investigated. The composites are prepared by employing the conventional stir casting technique, as it can
Externí odkaz:
https://doaj.org/article/2107c3b2e7d848cdab62a04c5f10a6d2
Publikováno v:
Journal of Natural Fibers, Vol 14, Iss 3, Pp 450-457 (2017)
This work deals with the investigation of Abrasive Water Jet Machining (AWJM) on banana fiber reinforced polyester composite. The composite is prepared with 20 wt. % of fiber through hand layup method followed by compression molding. Experiments are
Externí odkaz:
https://doaj.org/article/59662437ec1b49808084dc41e0c21eea
Publikováno v:
Modelling and Simulation in Engineering, Vol 2014 (2014)
The goal of the present experimental work is to optimize the electrical discharge machining (EDM) parameters of aluminum alloy (Al 6351) matrix reinforced with 5 wt.% silicon carbide (SiC) and 10 wt.% boron carbide (B4C) particles fabricated through
Externí odkaz:
https://doaj.org/article/82f359d5beae420d9efca36f5be09740