Zobrazeno 1 - 10
of 335
pro vyhledávání: '"I. Samardžić"'
Publikováno v:
Metalurgija, Vol 62, Iss 2, Pp 251-254 (2023)
This research focused on comparison of adhesion properties of three different primers for wide consumption. Tested primers differed in their price range, and the conducted experiment aimed to determine whether more expensive primers were providing be
Externí odkaz:
https://doaj.org/article/a69e07cba044439c9704c64be73d2838
Analysis of interconnection between physical and protective properties of two-component epoxy primer
Publikováno v:
Metalurgija, Vol 62, Iss 1, Pp 85-88 (2023)
This paper presents the research into protective properties of two-component epoxy primer obtained by measurements of the notch corrosion and by testing of the gloss as a physical property. In order to obtain different values of measured response, th
Externí odkaz:
https://doaj.org/article/1daa284f8a7243b7b953640446e5be24
Publikováno v:
Metalurgija, Vol 62, Iss 1, Pp 99-102 (2023)
This research analyses the influence of surface roughness on the rate of corrosion penetration into the steel. The test specimens were mechanically treated with fine abrasive jet to make their surface slightly rougher than it was in the initial state
Externí odkaz:
https://doaj.org/article/f384cdc0abef4f8cb55813c4693abcab
Publikováno v:
Metalurgija, Vol 61, Iss 1, Pp 185-188 (2022)
The article is a result of investigations which deals with the phase transformations of tool steel X155CrMoV12. The experimental data obtained was used to evaluate the resulting Continuous Cooling Transform (CCT) diagram, which consists of seven dila
Externí odkaz:
https://doaj.org/article/591fb0e630d444189b572e3cb0eb2f7a
Publikováno v:
Metalurgija, Vol 61, Iss 1, Pp 193-196 (2022)
The article deals with phase transformations and austenitizing behavior of the X155CrMoV12 tool steel. Dilatation analyses of a series of samples were performed at various cooling rates, chosen in the range from 10 °C/s to 0,1°C/s. Acquired experim
Externí odkaz:
https://doaj.org/article/27b966321a0a4f5f8f8b56858efda005
Publikováno v:
Metalurgija, Vol 61, Iss 2, Pp 355-358 (2022)
Agricultural tillage tools are exposed to various forms of wear during operation. Abrasive wear by soil particles is the most important wear form, and the most exposed to it are representatives of tools whose working parts are in direct contact with
Externí odkaz:
https://doaj.org/article/b642ccacc13041708ea0648d32cf98ff
Publikováno v:
Metalurgija, Vol 61, Iss 3-4, Pp 841-844 (2022)
This paper deals with analysis of the vehicle exhaust system quality and its influence on the results of measuring exhaust emissions of the Otto and Diesel motor vehicles. Results of eco-tests obtained from correct and faulty vehicle exhaust systems
Externí odkaz:
https://doaj.org/article/0797a71d7bc040c8b54bb4ffc5f40900
PB2054: HIP AND KNEE OSTEOARTHRITIS IN PHILADELPHIA CHROMOSOME-NEGATIVE MYELOPROLIFERATIVE NEOPLASMS
Autor:
H. Holik, I. Krečak, I. Samardžić, D. Pilipac, B. Coha, V. Gverić-Krečak, I. Vučinić Ljubičić, M. Lucijanić, I. Rajkovača Latić, L. Vinković, B. Miškić, S. Zupančić Šalek
Publikováno v:
HemaSphere, Vol 6, Pp 1925-1926 (2022)
Externí odkaz:
https://doaj.org/article/9a8bdb4f258f44409d454163847ce786
Publikováno v:
Metalurgija, Vol 59, Iss 4, Pp 470-472 (2020)
The durability of classic structural steels against various types of wear is generally low. Therefore, various types and combinations of resilient materials are constantly evolving, which are designed to reduce the cost of components replacement or r
Externí odkaz:
https://doaj.org/article/6f673203e35441329577098c4ec72aca
Publikováno v:
Metalurgija, Vol 58, Iss 1-2, Pp 87-90 (2019)
Structural components which are loaded in cyclic load mostly fail due to fatigue. The fatigue strength of metals as well as weld joint regions in metals depends on mechanical properties especially hardness, the size of defect and the size of grains.
Externí odkaz:
https://doaj.org/article/353239fa1ef54e6e8b78e40f6fb13d17