Zobrazeno 1 - 10
of 88
pro vyhledávání: '"I. S. Kainarskii"'
Autor:
I. S. Kainarskii, D. I. Gavrish
Publikováno v:
Refractories. 17:263-272
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::96a1053c257fa449310953be23d11352
https://doi.org/10.1007/bf01281610
https://doi.org/10.1007/bf01281610
Publikováno v:
Refractories. 17:753-757
The porosity of corundum intermediate products can be reduced by 6–7% by baking them at 1300°C and impregnating them three times with the melt of a 3/1 mixture of ammonium alum and potash alum while vibrating them to accelerate and improve the pro
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::d087a41d5ed5c728b2a92660002379f8
https://doi.org/10.1007/bf01319884
https://doi.org/10.1007/bf01319884
Autor:
Yu. D. Sagalevich, I. S. Kainarskii, D. I. Pankratov, Ya. M. Grinberg, L. A. Dergaputskaya, G. A. Slapichin, I. G. Orlova
Publikováno v:
Refractories. 19:80-83
It was shown that it is technically and economically advantageous to use ceramic materials for components which are subjected to the action of abrasive powders. Among the materials tested the best results were obtained with fired products fabricated
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::16a333697eb219faf727c73876755e0e
https://doi.org/10.1007/bf01281425
https://doi.org/10.1007/bf01281425
Autor:
I. S. Kainarskii, S. V. Lysak, B. G. Alapin, P. P. Krivoruchko, I. L. Boyarina, A. I. Portnova, É. V. Degtyareva
Publikováno v:
Refractories. 16:696-701
An investigation was carried out of the influence of certain additives on the sintering of chromic oxide. In an air medium, chromic oxide does not sinter at all without an additive. It achieves slight sintering with added TiO2 and a higher degree of
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::b55ab23e9bb8bcef656a666b247e9689
https://doi.org/10.1007/bf01280604
https://doi.org/10.1007/bf01280604
Publikováno v:
Refractories. 15:755-760
An investigation was carried out of the rheological and technological properties of silicon carbide suspensions. The optimal linear pH range of silicon carbide suspensions not containing an additive is 8.5–11. Within this range the ξ-potential is
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::8ac52276c7ed349a0d9ce773c1f8cff4
https://doi.org/10.1007/bf01284336
https://doi.org/10.1007/bf01284336
Publikováno v:
Refractories. 18:93-97
It was shown that specimens with an open porosity below 3% can be produced from zircon wet-ground in a vibromill, treated with acid, and containing over 80% grains smaller than 10μ including 60–70% grains smaller than 2μ; the density of the speci
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::9a2cb15ce1888494e5538e1632fdce3b
https://doi.org/10.1007/bf01319658
https://doi.org/10.1007/bf01319658
Publikováno v:
Refractories. 16:576-580
The quality of molding gypsum is good. It is chemically pure, does not set rapidly and gives a very strong mold.
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::05594fc31f5fb37214a3b886a0368507
https://doi.org/10.1007/bf01288001
https://doi.org/10.1007/bf01288001
Publikováno v:
Refractories. 16:368-372
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::4e77c09e606009b58ada1168a0405e75
https://doi.org/10.1007/bf01286211
https://doi.org/10.1007/bf01286211
Autor:
I. S. Kainarskii
Publikováno v:
Refractories. 18:449-457
The large, complex-shaped Dinas refractory products for coke ovens should be fired in a specialized tunnel kiln equipped with burners (of the roof or wall type) which will ensure a high degree of firing uniformity. The effective height of the kiln ch
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::78fa30184c91d45cf3a1accbcb9b5061
https://doi.org/10.1007/bf01288250
https://doi.org/10.1007/bf01288250
Autor:
I. S. Kainarskii
Publikováno v:
Refractories. 19:503-508
An investigation was carried out of ways of utilizing commercial alumina more efficiently in refractories production by improving the composition of the products and the technology of their manufacture. Commercial alumina should be used mainly for th
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::9c25fe682426037d122576f453e31c8f
https://doi.org/10.1007/bf01284277
https://doi.org/10.1007/bf01284277