Zobrazeno 1 - 10
of 75
pro vyhledávání: '"Ekici, Ergün"'
Publikováno v:
FME Transactions, Vol 52, Iss 3, Pp 343-359 (2024)
In the past few decades, fibre metal laminate (FML) machining has been facing critical challenges in quality control and tool wear monitoring due to the material's intrinsic heterogeneity and abrasiveness. Different drill tools have been used to inve
Externí odkaz:
https://doaj.org/article/8f0b1830c0e94f1b93c5f0f23aed19a0
Akademický článek
Tento výsledek nelze pro nepřihlášené uživatele zobrazit.
K zobrazení výsledku je třeba se přihlásit.
K zobrazení výsledku je třeba se přihlásit.
Autor:
Motorcu Ali Riza, Ekici Ergün
Publikováno v:
FME Transactions, Vol 50, Iss 3, Pp 441-460 (2022)
In this study, machinability tests were carried out to investigate the effects of control factors (cutting tool geometry, cutting speed, and feed rate) on the surface roughness (Ra), deviation from dimensional accuracy (Da_dev), roundness error (Re)
Externí odkaz:
https://doaj.org/article/6c700cc11ba24532ab6c60a1156debb7
Akademický článek
Tento výsledek nelze pro nepřihlášené uživatele zobrazit.
K zobrazení výsledku je třeba se přihlásit.
K zobrazení výsledku je třeba se přihlásit.
Publikováno v:
Polymer Composites; 8/10/2024, Vol. 45 Issue 11, p10050-10068, 19p
Publikováno v:
FME Transactions, Vol 49, Iss 2, Pp 356-366 (2021)
This study investigated the effects of drilling parameters and cutting tool coating conditions on the thrust force, surface roughness, and delamination factor in the drilling of fiber-reinforced carbon reinforced aluminum laminate (CARALL) composite,
Externí odkaz:
https://doaj.org/article/2bac3927cc9e468f91422defa3882cb3
Publikováno v:
FME Transactions, Vol 49, Iss 4, Pp 950-961 (2021)
In this study, the hole quality was investigated in the drilling of CARALL composite. In addition, the delamination factor calculation approaches of Chen, Davim, and Machado were compared in terms of the delamination damage at the hole entrance surfa
Externí odkaz:
https://doaj.org/article/465067d0c1df40bd906db27b42d8b32b
Publikováno v:
In Measurement January 2017 95:395-404
Autor:
Ekici Ergün, Gülesin Mahmut
Publikováno v:
Science and Engineering of Composite Materials, Vol 23, Iss 6, Pp 743-750 (2016)
In this study, the effects of the particle reinforcement ratio on cutting forces and surface roughness were investigated when milling particle-reinforced metal matrix composite (MMCp) produced by hot pressing with different cutting tools. Alumix 123
Externí odkaz:
https://doaj.org/article/c327e68678fe4e5181f13836966c84af
Publikováno v:
Science and Engineering of Composite Materials, Vol 23, Iss 4, Pp 435-445 (2016)
In this study, the effects of machining parameters on the material removal rate (MRR) and surface roughness (Ra) were investigated during the cutting of Al/B4C/Gr hybrid composites by wire electrical discharge machining (WEDM). Wire speed (WS), pulse
Externí odkaz:
https://doaj.org/article/4279fdc165cb456492547e4de2b73039