Zobrazeno 1 - 10
of 26
pro vyhledávání: '"Dj. Mandrino"'
Publikováno v:
Journal of Coatings Technology and Research. 12:1123-1131
Polyethylene glycol (PEG)- and polydimethylsiloxane (PDMS)-based corrosion protection coatings of the AISI 316L stainless steel surface were investigated. X-ray photoelectron spectroscopy (XPS) was used to confirm successful deposition of the coating
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::bcab9fb1ca67d39af6cde40ffc1c28a1
https://doi.org/10.1007/s11998-015-9698-8
https://doi.org/10.1007/s11998-015-9698-8
Publikováno v:
Applied Surface Science. 273:465-471
Zn–Al metallized film capacitors in two different production stages were investigated to explain the decrease of capacitors performance with time. Unsealed and sealed capacitors with different aluminium content in metallization layer were investiga
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::08b01322b616c153705b1f7e38bb08b0
https://doi.org/10.1016/j.apsusc.2013.02.063
https://doi.org/10.1016/j.apsusc.2013.02.063
Autor:
Dj. Mandrino, Črtomir Donik
Publikováno v:
Vacuum. 86:18-22
Thin oxide films were produced by the exposure of polished, sputter-cleaned metallic surfaces kept in UHV to several thousands of Langmuirs at 10−5 mbar oxygen yielding oxide layers of several nanometers. Metallic substrates used were iron, chromiu
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::29b9b90d20b17035a915539ecc99cb90
https://doi.org/10.1016/j.vacuum.2011.03.025
https://doi.org/10.1016/j.vacuum.2011.03.025
Publikováno v:
Engineering Failure Analysis. 16:1252-1261
A car’s drive shaft, machined from case-hardened steel that was carbo-nitrided, quenched and tempered, ruptured at an early stage of its use. Both sides of the fractured shaft were delivered for an investigation in order to discover the cause of th
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::ffdb0b33f38edb99cd2f28aea9ea09b4
https://doi.org/10.1016/j.engfailanal.2008.08.022
https://doi.org/10.1016/j.engfailanal.2008.08.022
Publikováno v:
Vacuum. 80:24-28
Fe 74 Si 11 B 14 Ni 1 soft-magnetic material was prepared as a powder using water atomisation. Using this method, powder particles of less than 45 μm in diameter were obtained after sieving. In the as-water-atomised condition the powder particles we
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::bcc8f874912188bd2bb1577728420307
https://doi.org/10.1016/j.vacuum.2005.07.020
https://doi.org/10.1016/j.vacuum.2005.07.020
Publikováno v:
Surface and Interface Analysis. 36:912-916
A soft magnetic composite material was prepared from a commercial, iron-based, soft magnetic powder. Its morphology and composition were examined using SEM, EDS and AES. The flat surface of the sample was found to be of a homogeneous composition, cor
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::a8538f702d782a348c0dd283c41e5c21
https://doi.org/10.1002/sia.1798
https://doi.org/10.1002/sia.1798
Publikováno v:
Surface and Interface Analysis. 36:917-920
Soft magnetic composites (SMCs) are produced by compressing together soft magnetic powders and a binding insulator material. In some applications these composites are able to replace electrical steel sheets or ferrites. Here we report on the developm
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::a8c0be6275805f9d6df96fc88afa0a2d
https://doi.org/10.1002/sia.1799
https://doi.org/10.1002/sia.1799
Publikováno v:
Surface and Interface Analysis. 34:346-351
Soft magnetic composite (SMC) materials for soft magnetic applications were developed. The most important property of SMC materials, especially those used in a high-frequency range, is that the soft magnetic powder particles are well insulated from e
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::807cba584d69a05b3ab6c9eebdd8501c
https://doi.org/10.1002/sia.1314
https://doi.org/10.1002/sia.1314
Publikováno v:
Applied Surface Science. 143:1-5
Scanning tunneling microscopy (STM) was used to study the surface of the 0.1% Sb alloyed electrical steel sheet. Material was subjected to thermal treatment to induce the surface segregation of impurities as well as alloying component. It was found t
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::0acebd2afdb7ef3306adba2d3809e197
https://doi.org/10.1016/s0169-4332(99)00090-2
https://doi.org/10.1016/s0169-4332(99)00090-2
Publikováno v:
Integrated Ferroelectrics. 4:13-19
LiTaO3 thin film from have been obtained by RF-magnetron sputtering from monocrystalline target. The films have been deposited on (111) silicon and platinum without substrate heating. The amorphous films were subsequently annealed in the electric fie
Externí odkaz:
https://explore.openaire.eu/search/publication?articleId=doi_________::9d03b0489c5e660cf85e591ea94e4a3f
https://doi.org/10.1080/10584589408018655
https://doi.org/10.1080/10584589408018655