Zobrazeno 1 - 10
of 124
pro vyhledávání: '"Chaosheng Song"'
Publikováno v:
Journal of Advanced Mechanical Design, Systems, and Manufacturing, Vol 18, Iss 5, Pp JAMDSM0059-JAMDSM0059 (2024)
A novel approach has been proposed to predesign to-be-modified tooth surface of spiral bevel gear with face milling manufacturing method, based on the preset of deviation of discretized points along normal direction. Five typical target geometry topo
Externí odkaz:
https://doaj.org/article/86fa7d096eef464cbae3323dfae9918c
Publikováno v:
Chinese Journal of Mechanical Engineering, Vol 36, Iss 1, Pp 1-18 (2023)
Abstract A three-dimensional conjugate tooth surface design method for Harmonic Drive with a double-circular-arc tooth profile is proposed. The radial deformation function of the flexspline (FS), obtained through Finite Element (FE) analysis, is inco
Externí odkaz:
https://doaj.org/article/015e1712f0bf4020bf4388f8719b03e0
Publikováno v:
Journal of Advanced Mechanical Design, Systems, and Manufacturing, Vol 17, Iss 6, Pp JAMDSM0080-JAMDSM0080 (2023)
In this paper, a novel cutter section is designed, which adds a linear transition section between the fillet and the major cutting edge for the three-faced cutter plate. By deriving the relative motion coupling relationship with the cutter plate, mac
Externí odkaz:
https://doaj.org/article/c6636c74f89c48bd89e01bdedf414220
Publikováno v:
Chinese Journal of Mechanical Engineering, Vol 34, Iss 1, Pp 1-17 (2021)
Abstract A compound oscillatory roller reducer (CORR) with a first-stage gear transmission and a second-stage oscillatory roller transmission is presented. The transmission principle of oscillatory roller transmission is introduced, and the tooth pro
Externí odkaz:
https://doaj.org/article/f35a5b3d6a2b4374815221243315bdb2
Publikováno v:
Journal of Advanced Mechanical Design, Systems, and Manufacturing, Vol 16, Iss 1, Pp JAMDSM0017-JAMDSM0017 (2022)
This paper proposes a calculation method for the contact ratio of internal beveloid gear pairs with small tooth number difference (IBGPSTND) based on the finite element method (FEM). The mathematical model and finite element model of the IBGPSTND are
Externí odkaz:
https://doaj.org/article/45d4308792ac4ee49180b4725a80efc3
Publikováno v:
Journal of Advanced Mechanical Design, Systems, and Manufacturing, Vol 16, Iss 1, Pp JAMDSM0003-JAMDSM0003 (2022)
To investigate the influence of the manufacturing parameters on mesh behaviors for harmonic gear drive, the mathematical model of slotting the circular spline was established using kinematic method based on the tooth profile of the circular spline. C
Externí odkaz:
https://doaj.org/article/632c99dd227d4e4d927cabcb01e9f5e1
Publikováno v:
Chinese Journal of Mechanical Engineering, Vol 32, Iss 1, Pp 1-15 (2019)
Abstract The current research of wind turbine drivetrain is mainly concentrated in dynamic characteristics of gearbox with a specific suspension of main shaft, such as one-point and two-point suspension. However, little attention is paid to the effec
Externí odkaz:
https://doaj.org/article/4c792de33b894baaaadd5a68f9a851b3
Impacts of Misalignments on Mesh Behaviors of Face-Hobbed Hypoid Gear Considering System Deformation
Publikováno v:
IEEE Access, Vol 7, Pp 79244-79253 (2019)
Considering the system deformation, a procedure to predict the mesh behaviors for face-hobbed hypoid gear pair in car rear axle was proposed based on the tooth surface model and the finite element analysis (FEA) tooth contact model. The mathematical
Externí odkaz:
https://doaj.org/article/3084536fc74944fda5cec3c634aebbe5
Publikováno v:
IEEE Access, Vol 7, Pp 111879-111889 (2019)
Taking the NW planetary gear transmission of an electric wheel hub as the research object, the mesh model was developed to calculate the mesh parameters using Masta. Then the lump parameter method was used to establish the dynamic model of the NW pla
Externí odkaz:
https://doaj.org/article/9d35c8cd949e48579317373ff556a7a4
Publikováno v:
Journal of Advanced Mechanical Design, Systems, and Manufacturing, Vol 14, Iss 6, Pp JAMDSM0086-JAMDSM0086 (2020)
The mathematical model of teeth distribution optimization for the promote gearbox is presented considering the objective functions such as the volume, efficiency, strength difference for the adjacent stages, and the design variables such as module, s
Externí odkaz:
https://doaj.org/article/715baff6ac7b46268f274b65cdffb5ae