Zobrazeno 1 - 10
of 94
pro vyhledávání: '"B. Shalchi Amirkhiz"'
Autor:
R. Alaghmandfard, P. Seraj, M. Sanjari, H. Pirgazi, C. Dharmendra, A.G. Odeshi, B. Shalchi Amirkhiz, M. Mohammadi
Publikováno v:
Journal of Materials Research and Technology, Vol 21, Iss , Pp 4093-4114 (2022)
The results of an investigation on the influence of strain rate on the microstructural and texture evolution, adiabatic shear band characterization, and deformation mechanism of electron beam melted Ti-6Al-4V vertically built cylindrical rods are pre
Externí odkaz:
https://doaj.org/article/2353bd684a1a4c9688f0acb5bd251f5f
Publikováno v:
Results in Materials, Vol 10, Iss , Pp 100178- (2021)
This study aims at assessing the effect of solution heat treatment (at a temperature just below the eutectic temperature) followed by various cooling rates on the microstructure and mechanical properties of additively manufactured AlSi10Mg and the ca
Externí odkaz:
https://doaj.org/article/31d2c615f9f84f04a539d91d6a53bbef
Publikováno v:
Materials & Design, Vol 194, Iss , Pp 108965- (2020)
In this study, C300 metal powders containing two different Ti contents (0.72 and 1.17 wt%) were used to additively manufacture maraging steel samples in both horizontal and vertical directions via laser powder bed fusion (LPBF) technique. The effect
Externí odkaz:
https://doaj.org/article/88758ffd7fec4dd3a75d664ee4668a83
Akademický článek
Tento výsledek nelze pro nepřihlášené uživatele zobrazit.
K zobrazení výsledku je třeba se přihlásit.
K zobrazení výsledku je třeba se přihlásit.
Autor:
M. Avateffazeli, S.I. Shakil, A. Hadadzadeh, B. Shalchi-Amirkhiz, H. Pirgazi, M. Mohammadi, M. Haghshenas
Publikováno v:
Materials Today Communications. 35:105804
Akademický článek
Tento výsledek nelze pro nepřihlášené uživatele zobrazit.
K zobrazení výsledku je třeba se přihlásit.
K zobrazení výsledku je třeba se přihlásit.
Autor:
S I, Shakil, A S, Zoeram, M, Avateffazeli, M, Roscher, H, Pirgazi, B, Shalchi-Amirkhiz, B, Poorganji, M, Mohammadi, M, Haghshenas
Publikováno v:
Micron (Oxford, England : 1993). 156
A dual-stage indentation test at ambient temperature including a constant indentation load rate followed by a constant indentation load-hold segment was employed to assess the time-dependent plastic deformation of cast and additive manufactured Al-Cu
Akademický článek
Tento výsledek nelze pro nepřihlášené uživatele zobrazit.
K zobrazení výsledku je třeba se přihlásit.
K zobrazení výsledku je třeba se přihlásit.
Publikováno v:
Journal of Materials Science & Technology. 35:1027-1038
Defect-free dissimilar Al/zinc coated steel and Al/AlSi coated steel welds were successfully fabricated by refill friction stir spot welding. However, Al alloy and uncoated steel could not be welded under the same welding condition. Al-Zn eutectic la
Autor:
S.I. Shakil, A.S. Zoeram, M. Avateffazeli, M. Roscher, H. Pirgazi, B. Shalchi-Amirkhiz, B. Poorganji, M. Mohammadi, M. Haghshenas
Publikováno v:
Micron. 156:103246